В корзине нет товаров
Bolt-on upgrade turbocharger for Audi A4 and Volkswagen Passat 1.8t petrol engines.
Equipped with reinforced machined from the solid compressor wheel - 48/60mm.
Turbine wheel - 48/45mm.
TurboSystems designed compressor housing and upgraded actuator.
Reinforced bearings to hold heavy loads. Air intake enlarged to 55mm.
| ENGINE BEARINGS | ||
 |
CON ROD BEARING SET |
|
| Part# | ||
| 4B2960H |
4B2960HX |
|
| Sizes | STD, .025, .25 | STD |
| Oil Clearance | Standard | + 0.001" Extra |
| Half Type | Identical Halves | |
| Material |
Tri-metal Hardened steel backs |
|
| Min Std Shaft Size |
1.888in / 47.956mm |
|
| Max Std Shaft Size |
1.8887in / 47.974mm |
|
| Min Std Tunnel Size |
2.0079in / 51.000mm |
|
| Max Std Tunnel Size |
2.0084in / 51.013mm |
|
| Max Wall at Crown |
0.0592in / 1.503mm |
0.0587in / 1.490mm |
| Max Overall Length |
0.673in / 17.10mm |
|
| Notes | ||
|
Diagram |
 |
|
Engines Nissan - 2.0 (SR20DE, SR20DET (not GTiR))
| Component | M7084/1UPR / M7084/1LPR |
| Min Crankshaft Diameter | 2.440 inch / 61.98mm |
| Max Crankshaft Diameter | 2.441inch / 62.00mm |
| Min Housing Diameter | 2.599 inch / 66.02 mm |
| Max Housing Diameter | 2.600 inch / 66.04 mm |
| Bearing Length | 0.787 inch / 19.99 mm |
| Max Wall Thickness | 0.000 inch / 0.00 mm |
| Component | M7084/2UPR / M7084/2LPR |
| Min Crankshaft Diameter | 2.440 inch / 61.98mm |
| Max Crankshaft Diameter | 2.441inch / 62.00mm |
| Min Housing Diameter | 2.599 inch / 66.02 mm |
| Max Housing Diameter | 2.600 inch / 66.04 mm |
| Bearing Length | 0.906 inch / 23.01 mm |
| Max Wall Thickness | 0.000 inch / 0.00 mm |
Specifications:
Coil Resistance: 9.1 Ohms / High Impedance
Dead Time: 0.45ms at 14 volts
Static Flow Rate @ 43.5 PSI ( 300kPa ) w/Gas: 1700 cc/min = 160 lb/hr
Static Flow Rate @ 50 PSI ( 350kPa ) w/Gas: 1875 cc/min = 180 lb/hr
Static Flow Rate @ 58 PSI ( 400kPa ) w/Gas: 2000 cc/min = 195 lb/hr
Connector: Bosch EV1
Injector Length: O-Ring to O-Ring: 62 mm
Injector Overall Length: 74 mm
Injector Body Diameter: 16mm
O-Ring: 14.5mm Viton
Acceptable Fuels: Gas/Petrol, alcohol/methanol, E85
Part number TW140AM
King Racing thrust washers kit
Honda - 1.6 1.7 1.8 2.0 2.1 2.2 2.3 2.4 (D16A, D16B, D16W, D16Y, D16Z, A18A, ES, ET, A20A, B16A, B17A1, B18A1, B18B1, B18B2, B18A, B20A SOHC, B18C1, B18C2, B18C5, B18C7, B20A, B21A, B21A1 DOHC, B20B, B20Z, D17A, D17Z, K20A3, K20A2, K20Z1, K24A, K24Z1, H22A, H22Z, F23A, F23Z)
Springs data:
Seat pressure - 82lbs @ 34.25mm
Open (lift) pressure - 220lbs @ 11.5mm
Spring coil bind - 20.70mm
Rate - 12.10lbs/mm
Max lift - 13.50mm
Outer spring outer diameter: 27.50mm
Outer spring inner diameter: 20.00mm
Inner spring outer diameter: 20.00mm
Inner spring inner diameter: 15.20mm
Set includes:
Dual springs: 16 pcs. SPR-TS1015/SU4
Titanium retainers: 16 pcs. RET-TS60/WRX1
Seats: 16 pcs. SEAT-TS/SUB4
|
Product detailed specification |
|
|
Bore size |
81.50mm |
|
Stroke |
86.40mm |
|
JE Pistons compression ratio (CR) |
8.5:1 |
|
OEM compression ratio (CR) |
9.5:1 |
|
Dome volume (CC) |
-11.3cm3 |
|
Compression height (CH) |
32.66mm |
|
Pin diameter |
20mm |
|
Features |
Accepts Turbo and Nitrous; FSR coated piston skirt |
|
Fits for |
VAG 1.8T 20V |
| Pairs & PN |
|
||||||
|---|---|---|---|---|---|---|---|
| Quantity | 5 | ||||||
| Crankshaft | 54.981 / 54.955 | ||||||
| Housing | 58.943 / 58.969 | ||||||
| Max Wall | 1.981 | ||||||
| Max Length | 19.101 |
