There are no items in cart
Direct replacement Single-mass flywheel made from Alloy steel (16MnCr5)
Used with aftermarket 240mm clutch kit.
Weight - 5kg.
Can be used with Sachs Performance clutch cover 883082000827
Clutch disc options:
Organic Sachs Performance (500+ Nm) - 881861999802
4pad ceramic Sachs Performance (up to 700 Nm) - 881861999809
6pad ceramic Sachs Performance (750+ Nm) - 881861000027
| ENGINE BEARINGS | ||
 |
CON ROD BEARING SET |
|
| Part# | ||
| 4B1606H |
4B1606HX |
|
| Sizes | STD, .025, .25, .50 | STD |
| Oil Clearance | Standard | + 0.001" Extra |
| Half Type | Identical Halves | |
| Material |
Tri-metal Hardened steel backs |
|
| Min Std Shaft Size |
1.8802" /47.758mm |
|
| Max Std Shaft Size |
1.8810" /47.778mm |
|
| Min Std Tunnel Size |
1.9921" /50.600mm |
|
| Max Std Tunnel Size |
1.9929" /50.619mm |
|
| Max Wall at Crown |
0.0553" / 1.405mm |
0.0548" /1.392mm |
| Max Overall Length |
0.748" / 19.00mm |
|
| Notes | Bearing has 1.65mm oil hole at crown | |
|
Diagram |
 |
|
Engines Audi 2.2 2.3 20V (incl. Turbo) S2, RS2, 200, S4, S6. 3B, 7A, AAN, ADU, ABY
Product detailed specification
Manufacturer: FCP Engineering
Model: FCPRHVW14450621-4
Profile: H-beam
C to C: 144mm
Big end diameter: 50.6mm
Pin diameter: 21mm
Quantity: 4 pcs., 8 pcs. ARP2000 3/8" bolts
Made of: forged steel 4340 EN24er
Advertised horsepower rating: 600HP (4 cylinder)
Advertised RPM rating: 9000RPM
Audi / VW / Seat / Skoda:
1.8T 20V (AEB, BAM, AWB and others)
|
Part number starting with 330 |
|
|
Athena advantages |
|
|
Reinforced material |
Asbestos free composite raw material OE approved |
|
Stainless steel ring (AISI304) |
Separate stainless steel rings assure maximum sealing around cylinder bore also on NOS and/or turbo charged engine where boost is over 2 bars. No head and block machining required |
|
Silicon beading |
Silicon-based beading is applied on critical areas to improve sealing around all cooling water and oil passages |
Cold side technical features:
Inducer: 42mm
Exducer: 56mm
Hot side technical features:
Inducer: 55mm
Exducer: 42mm
Kit includes turbocharger, gaskets, installation notice.
Enjoy the Walbro's new DCSS 39/50 in-tank fuel pump. Able to support an aggressive 700+ horsepower, with a super charger, this innovative dual pumping channel design delivers maximum pressure with superior fuel flow. Operating in both petrol and E85, this fuel pump comes with a check valve to avoid system leak-down and extended cranking at start-up. This superior design results in improved hot fuel flow, as well as minimal noise, increasing efficiency by 20% over conventional pumps, delivering unparalleled performance.
Specifications:
|
Product detailed specification |
|
|
Model number |
HEVN-1021D |
|
Head diameter |
30.50mm |
|
Stem diameter |
5.45mm |
|
Length |
108.65mm |
|
Material |
Black nitrited stainless steel |
|
Fits for |
Honda K20 K24 |
GENERAL |
|
| Temperature range | AECQ100 GRADE1 (-40 to +85˚C) |
| Reverse battery protection | Yes, internal |
| Operating voltage | 6-22V, immunity to transients according to ISO 7637 |
| Enclosure | IP 60, custom CNC machined aluminum |
| Connectors | 1 x 35 positions, AMP Automotive connector |
| PC communication | CAN BUS – Ecumaster interface, Peak or Kvaser |
| Display Type | TFT 800×480 |
| Brightness of display | 5″ – 600 cd/m2, 7″ – 1000 cd/m2 |
|
Product detailed specification |
|
|
Bore size |
84.50mm |
|
Stroke |
89.60mm |
|
JE Pistons compression ratio (CR) |
9.5:1 |
|
OEM compression ratio (CR) |
10.2:1 |
|
Dome volume (CC) |
-14.7cm3 |
|
Compression height (CH) |
32.40mm |
|
Pin diameter |
22mm |
|
Features |
Accepts Turbo and Nitrous; coated FSR skirt |
|
Fits for |
BMW - 3.0 24V Turbo (N55B30, S55B30) |
| Position | |||||||
|---|---|---|---|---|---|---|---|
| Pairs & PN |
|
||||||
| Quantity | 1 | ||||||
| Crankshaft | 66.965 / 66.972 | ||||||
| Housing | 0.000 / 0.000 | ||||||
| Max Wall | 2.510 | ||||||
| Max Length | 18.352 |
| ENGINE BEARINGS | ||
 |
CON ROD BEARING SET |
|
| Part# | ||
| 4B1912H |
4B1912HX |
|
| Sizes | STD, 025, .25 | STD |
| Oil Clearance | Standard | + 0.001" Extra |
| Half Type | Identical Halves | |
| Material |
Tri-metal Hardened steel backs |
|
| Min Std Shaft Size |
1.889in / 47.98mm |
|
| Max Std Shaft Size |
1.8898in / 48mm |
|
| Min Std Tunnel Size |
2.008in / 51.004mm |
|
| Max Std Tunnel Size |
2.0088in / 51.024mm |
|
| Max Wall at Crown |
0.0589in / 1.496mm |
0.0584in / 1.483mm |
| Max Overall Length |
0.7638in / 19.4mm |
|
| Notes | ||
|
Diagram |
 |
|
Product detailed specification
Manufacturer: FCP Engineering
Model: FCPRHN15255321
Profile: H-beam
C to C: 152.50mm
Big end diameter: 53mm
Pin diameter: 21mm
Quantity: 6 pcs., 12 pcs. ARP2000 3/8" bolts
Made of: forged steel 4340 EN24er
Advertised horsepower rating: 800HP (6 cylinder)
Advertised RPM rating: 9000RPM
Nissan Skyline GTR - 3.0 24V (RB30DET)
Athena Racing 338 series multilayer steel (MLS) cylinder head gasket.
Athena MLS gaskets are designed to suit the requirements of today’s competition engines offering enhanced sealing compared to the OEM product. The gaskets are assembled from 2-5 layers of high quality stainless and spring steels.
Part number 338471R
Gasket thickness: 1.00mm
Bore size: 89.00mm
|
Part number starting with 338 |
|
|
Athena advantages |
|
|
Optimized radius embossing shape |
The round shape of the embossing increases sealing on cylinder bore, oil and cooling water passages and improves spring back strength |
|
Advanced stopper technology |
State of the technology enhances sealing pressure around the cylinder. Highest sealing properties in high power engines |
|
Coating technology |
Designed & engineered by Athena the special coating applied on steel surfaces, improves temperature resistance & reliability of the head gasket |
