В корзине нет товаров
|
Part number starting with 330 |
|
|
Athena advantages |
|
|
Reinforced material |
Asbestos free composite raw material OE approved |
|
Stainless steel ring (AISI304) |
Separate stainless steel rings assure maximum sealing around cylinder bore also on NOS and/or turbo charged engine where boost is over 2 bars. No head and block machining required |
|
Silicon beading |
Silicon-based beading is applied on critical areas to improve sealing around all cooling water and oil passages |
|
|||||||
| Quantity | 4 | ||||||
| Crankshaft | 47.777 / 47.757 | ||||||
| Housing | 50.599 / 50.620 | ||||||
| Max Wall | 1.402 | ||||||
| Max Length | 18.971 |
|
Product detailed specification |
|
|
Bore size |
81.50mm |
|
Stroke |
86.40mm |
|
Wiseco compression ratio (CR) |
8.5:1 |
|
OEM compression ratio (CR) |
9.5:1 |
|
Dome volume (CC) |
-7cm3 |
|
Compression height (CH) |
32.71mm |
|
Pin diameter |
20mm |
|
Features |
Accepts Turbo and Nitrous, Round piston skirt |
|
Fits for |
VAG - 1.8T 20V |
Athena Racing 338 series multilayer steel (MLS) cylinder head gasket.
Athena MLS gaskets are designed to suit the requirements of today’s competition engines offering enhanced sealing compared to the OEM product. The gaskets are assembled from 2-5 layers of high quality stainless and spring steels.
Part number 338486R
Gasket thickness: 0.85mm
Bore size: 84.00mm
|
Part number starting with 338 |
|
|
Athena advantages |
|
|
Optimized radius embossing shape |
The round shape of the embossing increases sealing on cylinder bore, oil and cooling water passages and improves spring back strength |
|
Advanced stopper technology |
State of the technology enhances sealing pressure around the cylinder. Highest sealing properties in high power engines |
|
Coating technology |
Designed & engineered by Athena the special coating applied on steel surfaces, improves temperature resistance & reliability of the head gasket |
|
Product detailed specification |
|
|
Bore size |
82.00mm |
|
Stroke |
86.40mm |
|
JE Pistons compression ratio (CR) |
8.5:1 |
|
OEM compression ratio (CR) |
9.3:1 |
|
Dome volume (CC) |
-8cm3 |
|
Compression height (CH) |
30.86mm |
|
Pin diameter |
21mm |
|
Features |
Accepts Turbo and Nitrous; Round skirt |
|
Fits for |
Audi S4, RS4, A6 - 2.7 30V |
Информация толкателя:
Наружный диаметр - 34.97mm
Внутренний диаметр - 33.10mm
Наружная высота - 26.30mm
Длина стебля - 14.70mm
Диаметр шпильки - 7.00mm
Вес - 50g
8 pcs. FCP Engineering механические толкатели.
Кованая сталь, нитридная упрочненная поверхность, HRC 50.
Installed follower height to camshaft must be adjusted with lash caps (not included).
Высота установленного толкателя до распределительного вала должна быть отрегулирована с помощью tаблеткоми регулировония (не входит в комплект)
Valve guide info:
Part number: FCPVGA/20
Material: Bronze
Length: 38mm
Inner diameter: 7mm
Outer diameter: 12.07mm
For intake and exhaust valves
|
Product detailed specification |
|
|
Bore size |
82.00mm |
|
Stroke |
86.40mm |
|
Wiseco compression ratio (CR) |
8.5:1 |
|
OEM compression ratio (CR) |
9.5:1 |
|
Dome volume (CC) |
-7cm3 |
|
Compression height (CH) |
32.71mm |
|
Pin diameter |
20mm |
|
Features |
Accepts Turbo and Nitrous, Round piston skirt |
|
Fits for |
VAG - 1.8T 20V |
