В корзине нет товаров
Enjoy the Walbro's new DCSS 39/50 in-tank fuel pump. Able to support an aggressive 700+ horsepower, with a super charger, this innovative dual pumping channel design delivers maximum pressure with superior fuel flow. Operating in both petrol and E85, this fuel pump comes with a check valve to avoid system leak-down and extended cranking at start-up. This superior design results in improved hot fuel flow, as well as minimal noise, increasing efficiency by 20% over conventional pumps, delivering unparalleled performance.
Specifications:
|
Product detailed specification |
|
|
Model number |
TEVI-1014 |
|
Head diameter |
29.00mm |
|
Stem diameter |
5.97mm |
|
Length |
99.10mm |
|
Material |
Inconel |
|
Fits for |
Toyota Supra - 3.0 (2JZGE, 2JZGTE) |
|
Product detailed specification |
|
|
Model number |
TIVN-1014 |
|
Head diameter |
33.50mm |
|
Stem diameter |
5.98mm |
|
Length |
98.55mm |
|
Material |
Black nitrided stainless steel |
|
Fits for |
Toyota Supra - 3.0 (2JZGE, 2JZGTE) |
|
Product detailed specification |
|
|
Model number |
BMEVI-1030PSL |
|
Head diameter |
31.00mm |
|
Stem diameter |
5.98mm |
|
Length |
122.80mm |
|
Material |
Inconel/Nimonic |
|
Fits for |
BMW M3 E36 - 3.2 (S50B32) |
|
Product detailed specification |
|
|
Model number |
VWEVI-1044SS |
|
Head diameter |
30.15mm |
|
Stem diameter |
5.96mm |
|
Length |
102.50mm |
|
Material |
Inconel |
|
Fits for |
Audi A3, VW Golf R32 - 3.2 24V V6 VR6 |
Product info:
Length: 1200mm
Width: 23mm
Number of tooth: 150
Gates' timing belts offer a precision fit with easy installation and no interference engine damage - exactly what you've come to expect from the worldwide leader in timing belts.
- Tensile cord reinforced with premium, high-strength glass cords.
- Gripping teeth with aramid fiber technology and high saturation HNBR elastomeric composites for exceptional durability and heat resistance.
- Wear-resistant tooth jacket supported by reinforced nylon fabric and double-tooth stability.
- The superior construction of Gates timing belts makes them 300 percent stronger than the standard aftermarket belt while providing up to three times the heat resistance.
Specifications:
Coil Resistance: 9.1 Ohms / High Impedance
Dead Time: 0.45ms at 14 volts
Static Flow Rate @ 43.5 PSI ( 300kPa ) w/Gas: 1700 cc/min = 160 lb/hr
Static Flow Rate @ 50 PSI ( 350kPa ) w/Gas: 1875 cc/min = 180 lb/hr
Static Flow Rate @ 58 PSI ( 400kPa ) w/Gas: 2000 cc/min = 195 lb/hr
Connector: Bosch EV1
Injector Length: O-Ring to O-Ring: 62 mm
Injector Overall Length: 74 mm
Injector Body Diameter: 16mm
O-Ring: 14.5mm Viton
Acceptable Fuels: Gas/Petrol, alcohol/methanol, E85
|
Product detailed specification |
|
|
Model number |
BMIVN-1033SL |
|
Head diameter |
35.65mm |
|
Stem diameter |
5.97mm |
|
Length |
121.30mm |
|
Material |
Black nitrited stainless steel |
|
Fits for |
BMW M3 E36 - 3.2 (S50B32) |
Информация толкателя:
Наружный диаметр - 34.97mm
Внутренний диаметр - 33.10mm
Наружная высота - 26.30mm
Длина стебля - 14.70mm
Диаметр шпильки - 7.00mm
Вес - 50g
8 pcs. FCP Engineering механические толкатели.
Кованая сталь, нитридная упрочненная поверхность, HRC 50.
Installed follower height to camshaft must be adjusted with lash caps (not included).
Высота установленного толкателя до распределительного вала должна быть отрегулирована с помощью tаблеткоми регулировония (не входит в комплект)
