4B11

Mitsubishi EVO X 2.0 4B11T ACL Race Pleuellager Satz 4B1236H-STD

ENGINE BEARINGS
	CON ROD BEARING SET
	Part#
	4B1236H	4B1236HX
Sizes	STD, .025, .25	STD
Oil Clearance	Standard	+ 0.001" Extra
Half Type	Identical Halves
Material	Tri-metal Hardened steel backs
Min Std Shaft Size	2.0454in / 51.954 mm
Max Std Shaft Size	2.0461in / 51.972 mm
Min Std Tunnel Size	2.1654 in / 55.000 mm
Max Std Tunnel Size	2.1657 in / 55.010 mm
Max Wall at Crown	0.0591in / 1.500 mm	0.0585in / 1.487 mm
Max Overall Length	0.669 in / 17.00 mm
Notes	-
Diagram (Top View)

Engines Mitsubishi EVO X - 2.0 Turbo (4B11T)

75,00 €

Mitsubishi EVO X 2.0 4B11T ACL Race Pleuellager Satz 4B1236H-0.25

ENGINE BEARINGS
	CON ROD BEARING SET
	Part#
	4B1236H	4B1236HX
Sizes	STD, .025, .25	STD
Oil Clearance	Standard	+ 0.001" Extra
Half Type	Identical Halves
Material	Tri-metal Hardened steel backs
Min Std Shaft Size	2.0454in / 51.954 mm
Max Std Shaft Size	2.0461in / 51.972 mm
Min Std Tunnel Size	2.1654 in / 55.000 mm
Max Std Tunnel Size	2.1657 in / 55.010 mm
Max Wall at Crown	0.0591in / 1.500 mm	0.0585in / 1.487 mm
Max Overall Length	0.669 in / 17.00 mm
Notes	-
Diagram (Top View)

Engines Mitsubishi EVO X - 2.0 Turbo (4B11T)

75,00 €

Mitsubishi EVO X 4B11T ACL Anlaufscheiben 1T1237-STD

Teilenummer 1T1237-STD
ACL Anlaufscheiben Kit
Mitsubishi EVO X - 2.0 16V (4B11T)

15,00 €

Mitsubishi EVO X 4B11T ACL Race Series Hauplager Satz 5M1237H-STD

ENGINE BEARINGS
	MAIN BEARING SET
	Part#
	5M1237H	5M1237HX
Sizes	STD, .025, .25	STD
Oil Clearance	Standard	+ 0.001" Extra
Half Type	Upper & Lower
Material	Tri-Metal
Min Std Shaft Size	2.0462 in / 51.973 mm
Max Std Shaft Size	2.0467 in / 51.985 mm
Min Std Tunnel Size	2.2047 in / 56.000 mm
Max Std Tunnel Size	2.2054 in / 56.018 mm
Max Wall at Crown	0.0786 in / 1.996 mm	0.0781 in / 1.983 mm
Max Overall Length	0.709 in / 18.00 mm
Notes	-
Diagram (Top View)

Engines Mitsubishi EVO X - 2.0 16V (4B11T)

139,00 €

Mitsubishi EVO X 4B11T ACL Race Series Hauplager Satz 5M1237H-0.25

ENGINE BEARINGS
	MAIN BEARING SET
	Part#
	5M1237H	5M1237HX
Sizes	STD, .025, .25	STD
Oil Clearance	Standard	+ 0.001" Extra
Half Type	Upper & Lower
Material	Tri-Metal
Min Std Shaft Size	2.0462 in / 51.973 mm
Max Std Shaft Size	2.0467 in / 51.985 mm
Min Std Tunnel Size	2.2047 in / 56.000 mm
Max Std Tunnel Size	2.2054 in / 56.018 mm
Max Wall at Crown	0.0786 in / 1.996 mm	0.0781 in / 1.983 mm
Max Overall Length	0.709 in / 18.00 mm
Notes	-
Diagram (Top View)

Engines Mitsubishi EVO X - 2.0 16V (4B11T)

139,00 €

Kolbenschmidt plastigage Meßstreifen für Gleitlager 120000417001

Teilenummer 50009880.
Kolbenschmidt Plastigage Meßstreifen Gleitlager Kit (10 Stk.).
Messstreifen zur Bestimmung des Lagerspiels bei Gleitlager.

15,00 €

ACL Meßstreifen für Gleitlager / Flexigauge AG-1 (Grün)

1. Remove the bearing cap, wipe the journal and bearing shell clear of oil.
2. Place a piece of Flexigauge across the bearing at the crown (see Figure 1).
3. Install the bearing cap and using a Torque Wrench tighten the bolts to the correct tension.
4. DO NOT REVOLVE THE SHAFT OR BEARINGS.
5. Remove bearing cap. The Flexigauge will be adhering either to the bearing or shaft.
6. Compare the width of the flattened Flexigauge with the graduation of the envelope. The figure within the graduations indicates the clearance in thousandths of an inch of millimetres, depending on which side of the envelope is used. (See Figure 2).
7. Taper is indicated when Flexigauge is wider at one end than the other, the amount of taper being the difference between the readings. The widest part of the Flexigauge represents the area of least clearance. “Barrelling” of the shaft when the Flexigauge is wider in the centre of the bearing.

16,00 €

Permatex Ultra Slick Montageschmierstoff für Motorlager 118ml (1 Stk.)

18,00 €