Click here to open old website version
All categories
Parts by Car
Go
Parts by Car
Go
Parts by:
Category

Mitsubishi

Mitsubishi 4G63T 4G64 ACL Race main bearings 5M1219H-STD
ENGINE BEARINGS
rods.jpg

MAIN BEARING SET

Part#
5M1219H

 
5M1219HX

 
Sizes STD,.025, .25 STD
Oil Clearance Standard + 0.001" Extra
Half Type Upper & Lower
Material Tri-Metal
Min Std Shaft Size

2.2435in / 56.985mm

Max Std Shaft Size

2.2441in / 57.000mm

Min Std Tunnel Size

2.4016in / 61.000mm

Max Std Tunnel Size

2.4024in / 61.021mm

Max Wall at Crown

0.0783in / 1.990mm

0.0778in / 1.977mm

Max Overall Length

0.8268in / 21.00mm

Notes For engines equipped with thrust washers

Diagram       
(Top View) 

5M1219H.jpg
Engines Mitsubishi - 2.0 (4G63, 4G63-T, 4G64-S4)
€95.00
ACL plain bearing measuring tape/flexigauge AG-1 (Green)
1. Remove the bearing cap, wipe the journal and bearing shell clear of oil.
2. Place a piece of Flexigauge across the bearing at the crown (see Figure 1).
3. Install the bearing cap and using a Torque Wrench tighten the bolts to the correct tension.
4. DO NOT REVOLVE THE SHAFT OR BEARINGS.
5. Remove bearing cap. The Flexigauge will be adhering either to the bearing or shaft.
6. Compare the width of the flattened Flexigauge with the graduation of the envelope. The figure within the graduations indicates the clearance in thousandths of an inch of millimetres, depending on which side of the envelope is used. (See Figure 2).
7. Taper is indicated when Flexigauge is wider at one end than the other, the amount of taper being the difference between the readings. The widest part of the Flexigauge represents the area of least clearance. “Barrelling” of the shaft when the Flexigauge is wider in the centre of the bearing.
€16.00
Mitsubishi 4G63T 4G64 ACL Race main bearings 5M1219HX-STD
ENGINE BEARINGS
rods.jpg

MAIN BEARING SET

Part#
5M1219H

 
5M1219HX

 
Sizes STD,.025, .25 STD
Oil Clearance Standard + 0.001" Extra
Half Type Upper & Lower
Material Tri-Metal
Min Std Shaft Size

2.2435in / 56.985mm

Max Std Shaft Size

2.2441in / 57.000mm

Min Std Tunnel Size

2.4016in / 61.000mm

Max Std Tunnel Size

2.4024in / 61.021mm

Max Wall at Crown

0.0783in / 1.990mm

0.0778in / 1.977mm

Max Overall Length

0.8268in / 21.00mm

Notes For engines equipped with thrust washers

Diagram       
(Top View) 

5M1219H.jpg
Engines Mitsubishi - 2.0 (4G63, 4G63-T, 4G64-S4)
€95.00
Mitsubishi 4G63T 4G64 ACL Race main bearings 5M1219H-0.25
ENGINE BEARINGS
rods.jpg

MAIN BEARING SET

Part#
5M1219H

 
5M1219HX

 
Sizes STD,.025, .25 STD
Oil Clearance Standard + 0.001" Extra
Half Type Upper & Lower
Material Tri-Metal
Min Std Shaft Size

2.2435in / 56.985mm

Max Std Shaft Size

2.2441in / 57.000mm

Min Std Tunnel Size

2.4016in / 61.000mm

Max Std Tunnel Size

2.4024in / 61.021mm

Max Wall at Crown

0.0783in / 1.990mm

0.0778in / 1.977mm

Max Overall Length

0.8268in / 21.00mm

Notes For engines equipped with thrust washers

Diagram       
(Top View) 

5M1219H.jpg
Engines Mitsubishi 4 cylinder 2.0 (4G63, 4G63-T, 4G64-S4)
€95.00
Mitsubishi 4G63T 4G64 ACL Race Calico main bearings 5M1219HC-STD
Sizes STD, .025, .25
Oil Clearance Standard
Half Type Upper & Lower
Material Tri-Metal
Min. Std Shaft Size 2.2435in / 56.985mm
Max. Std Shaft Size 2.2441in / 57.000mm
Min. Std Tunnel Size 2.4016in / 61.000mm
Max. Std Tunnel Size 2.4024in / 61.021mm
Max Wall at Crown 0.0783in / 1.990mm
Max Overall Length 0.8268in / 21.00mm
Notes For engines equipped with thrust washers

CT-1 is a Dry Film Lubricant coating that helps reduce friction and abrasive wear. It provides intermittent dry lubrication and is not affected by dust or dirt. CT-1 is specifically engineered to withstand the extreme conditions of today's high performance engines. Professional engine builders enjoy a higher level of confidence with increased embedability, strength and durability.

€199.00
ACL oil pump Mitsubishi Evo 4-9 OPMB1176
  • Meets or Exceeds OEM pump flow
  • Individually inspected and tested to assure pressure and flow specifications
  • Twelve-month, 12,000 mile warranty
  • TSI6949 and ISO certification
  • Die cast ADC-12 aluminum housing for added strength and reduced weight
  • Steel copper alloy gerotor sets for dependable service and reliability
  • Tight tolerances for optimum pressure and flow performance
€449.00
1 2