There are no items in cart
Product info:
Length: 1200mm
Width: 23mm
Number of tooth: 150
Gates' timing belts offer a precision fit with easy installation and no interference engine damage - exactly what you've come to expect from the worldwide leader in timing belts.
- Tensile cord reinforced with premium, high-strength glass cords.
- Gripping teeth with aramid fiber technology and high saturation HNBR elastomeric composites for exceptional durability and heat resistance.
- Wear-resistant tooth jacket supported by reinforced nylon fabric and double-tooth stability.
- The superior construction of Gates timing belts makes them 300 percent stronger than the standard aftermarket belt while providing up to three times the heat resistance.
|
Product detailed specification |
|
|
Head diameter |
32mm |
|
Stem diameter |
7mm |
|
Length |
95.5mm |
|
Fits for |
Audi / VW - 1.8 16V, 2.0 16V, 2.2T 20V, 2.3 20V (KR, PL, 6A, 9A, ABF, 3B, AAN, ABY, ADU, 7A) |
8740 Chrome Moly: Until the development of today’s modern alloys, chrome moly was popularly considered a high strength material. Now viewed as only moderate strength, 8740 chrome moly is seen as a good tough steel, with adequate fatigue properties for most racing applications, but only if the threads are rolled after heat-treatment, as is the standard ARP production practice. Typically, chrome moly is classified as a quench and temper steel, that can be heat-treated to deliver tensile strengths between 180,000 and 210,000 psi
Athena Racing 330 series Cooper Ring cylinder head gasket.
For specific high horsepower applications, engine performance can be significantly improved by using Athena Cooper Ring gaskets, that are supplied with INOX steel ring. This technology outperforms conventional fire ring solutions.
Cooper Rings are oversize (also fits for oversize bores).
|
Part number starting with 330 |
|
|
Athena advantages |
|
|
Reinforced material |
Asbestos free composite raw material OE approved |
|
Stainless steel ring (AISI304) |
Separate stainless steel rings assure maximum sealing around cylinder bore also on NOS and/or turbo charged engine where boost is over 2 bars. No head and block machining required |
|
Silicon beading |
Silicon-based beading is applied on critical areas to improve sealing around all cooling water and oil passages |
|
Product detailed specification |
|
|
Bore size |
82.50mm |
|
Stroke |
92.80mm |
|
Wiseco compression ratio (CR) |
8.5:1 |
|
OEM compression ratio (CR) |
10.5:1 |
|
Dome volume (CC) |
-11cm3 |
|
Compression height (CH) |
30.60mm |
|
Pin diameter |
21mm |
|
Features |
FSR series skirt |
|
Fits for |
VW / Seat - 2.0 16V ABF |
| ENGINE BEARINGS | ||
 |
CON ROD BEARING SET |
|
| Part# | ||
| 4B1606H |
4B1606HX |
|
| Sizes | STD, .025, .25, .50 | STD |
| Oil Clearance | Standard | + 0.001" Extra |
| Half Type | Identical Halves | |
| Material |
Tri-metal Hardened steel backs |
|
| Min Std Shaft Size |
1.8802" /47.758mm |
|
| Max Std Shaft Size |
1.8810" /47.778mm |
|
| Min Std Tunnel Size |
1.9921" /50.600mm |
|
| Max Std Tunnel Size |
1.9929" /50.619mm |
|
| Max Wall at Crown |
0.0553" / 1.405mm |
0.0548" /1.392mm |
| Max Overall Length |
0.748" / 19.00mm |
|
| Notes | Bearing has 1.65mm oil hole at crown | |
|
Diagram |
 |
|
CT-1 is a Dry Film Lubricant coating that helps reduce friction and abrasive wear. It provides intermittent dry lubrication and is not affected by dust or dirt. CT-1 is specifically engineered to withstand the extreme conditions of today's high performance engines. Professional engine builders enjoy a higher level of confidence with increased embedability, strength and durability.
|
Product detailed specification |
|
|
Bore size |
83.50mm |
|
Stroke |
92.80mm |
|
JE Pistons compression ratio (CR) |
12.8:1 |
|
OEM compression ratio (CR) |
10.5:1 |
|
Dome volume (CC) |
8.9cm3 |
|
Compression height (CH) |
29.59mm |
|
Pin diameter |
20mm |
|
Features |
Coated FSR series skirt |
|
Fits for |
VW - 2.0 16V 9A |
