There are no items in cart
Diameter: 240mm
Compared to volume production pressure plates, SACHS Performance pressure plates have a higher transmittable torque and are less sensitive to thrust loading. Depending on the requirements, they are used with different discs. Higher pedal forces might occur.
| Min Std Shaft Size |
1.7707in / 44.975mm |
|
| Max Std Shaft Size |
1.7713in / 44.991mm |
|
| Min Std Tunnel Size |
1.8898in / 48.000mm |
|
| Max Std Tunnel Size |
1.8904in / 48.016mm |
|
| Max Wall at Crown |
0.0588in / 1.493mm |
|
| Max Overall Length |
0.709in / 18.00mm |
|
|
Part number starting with 330 |
|
|
Athena advantages |
|
|
Reinforced material |
Asbestos free composite raw material OE approved |
|
Stainless steel ring (AISI304) |
Separate stainless steel rings assure maximum sealing around cylinder bore also on NOS and/or turbo charged engine where boost is over 2 bars. No head and block machining required |
|
Silicon beading |
Silicon-based beading is applied on critical areas to improve sealing around all cooling water and oil passages |
|
Product detailed specification |
|
|
Bore size |
84.50mm |
|
Stroke |
95.90mm |
|
JE Pistons compression ratio (CR) |
11.5:1 |
|
OEM compression ratio (CR) |
10.9:1/11.3:1 |
|
Dome volume (CC) |
-7.40cm3 |
|
Compression height (CH) |
34.50mm |
|
Pin diameter |
20mm |
|
Features |
Accepts Turbo and Nitrous; Full round skirt |
|
Fits for |
VW / Audi 3.2 24V R32 |
| ENGINE BEARINGS | ||
 |
MAIN BEARING SET |
|
| Part# | ||
| 5M1913H |
5M1913HX |
|
| Sizes | STD, 025, .25 | STD |
| Oil Clearance | Standard | + 0.001" Extra |
| Half Type | Identical Halves | |
| Material | Tri-Metal | |
| Min Std Shaft Size |
2.1644in / 54.976mm |
|
| Max Std Shaft Size |
2.1654in / 55mm |
|
| Min Std Tunnel Size |
2.3622in / 60mm |
|
| Max Std Tunnel Size |
2.363in / 60.02mm |
|
| Max Wall at Crown |
0.0986in / 2.504mm |
0.0981in /2.491mm |
| Max Overall Length |
0.7874in / 20mm |
|
| Notes | ||
|
Diagram |
 |
|
|
Part number starting with 330 |
|
|
Athena advantages |
|
|
Reinforced material |
Asbestos free composite raw material OE approved |
|
Stainless steel ring (AISI304) |
Separate stainless steel rings assure maximum sealing around cylinder bore also on NOS and/or turbo charged engine where boost is over 2 bars. No head and block machining required |
|
Silicon beading |
Silicon-based beading is applied on critical areas to improve sealing around all cooling water and oil passages |
|
Component |
1937 |
|
Halves |
Identical Halves |
|
Material code |
F780 |
|
Min Std Shaft Size |
1.9677 in / 49.98 mm |
|
Max Std Shaft Size |
1.9685 in / 50 mm |
|
Min Std Tunnel Size |
0.02 in / 0.54 mm |
|
Max Std Tunnel Size |
0.02 in / 0.54 mm |
|
Max Overall Length |
0.7874 in / 20 mm |
|
Max Wall At Crown |
0.0789 in / 2 mm |
Product detailed specification
Manufacturer: FCP Engineering
Diameter: 228mm
Compared to volume production pressure plates, SACHS Performance pressure plates have a higher transmittable torque and are less sensitive to thrust loading. Depending on the requirements, they are used with different discs. Higher pedal forces might occur.
BMW
1 201 832
1 202 033
1 202 265
1 202 452
Clutch disc with special organic clutch friction material.
Diameter: 240mm
Number of teeth: 23
Hub profile: 21.9x24.3-23N
Transmittable torque: 520Nm
Manufacturer compare numbers:
Audi
050 141 117 E
074 141 117 G
074 141 117 H
077 141 117 L
078 141 117
These high performance clutch plates from Sachs are a direct replacement for an OEM clutch plate and have a much more aggressive friction surface which allows them to handle up to 40% more torque. This makes them ideal for competition cars where a more aggressive clutch actuation is acceptable. For these clutch plates to operate at their maximum torque capacity they should be used with a Sachs high performance clutch cover.
