Jūsų krepšelis yra tuščias
| ENGINE BEARINGS | ||||
 |
CON ROD BEARING SET |
MAIN BEARING SET |
||
| Part# | Part# | |||
| 4B2904H |
4B2904HX |
5M2908H |
5M2908HX |
|
| Sizes | STD, .025, .25 | STD | STD, .025, .25 | STD |
| Oil Clearance | Standard | + 0.001" Extra | Standard | + 0.001" Extra |
| Half Type | Identical Halves | Upper & Lower | ||
| Material |
Tri-metal Hardened steel backs |
Tri-Metal | ||
| Min Std Shaft Size |
1.9995in / 50.787 mm |
2.0862 in / 52.991 mm |
||
| Max Std Shaft Size |
2.0003in / 50.807 mm |
2.0866 in / 53.000 mm |
||
| Min Std Tunnel Size |
2.1219 in / 53.897 mm |
2.2330 in / 56.717 mm |
||
| Max Std Tunnel Size |
2.1226 in / 53.913 mm |
2.2337 in / 56.735 mm |
||
| Max Wall at Crown |
0.0605in / 1.536 mm |
0.0600in / 1.523 mm |
0.0726 in / 1.843 mm |
0.0720 in / 1.830 mm |
| Max Overall Length |
0.768 in / 19.50 mm |
0.817 in / 20.75 mm (2908H/HX) 0.955 in / 24.25 mm (2909H/HX) |
||
| Notes | - | - | ||
|
Diagram |
 |
2908H & HX - Positions 1,2,4,5
2909H & HX - Position 3
|
||
| THRUSTWASHER SET | ||||
| Part# | Material | |||
| Sizes | Notes | - | ||
Prekės kodas 50009880.
Kolbenschmidt plastikinių matavimo juostelių rinkinys (10 vnt.).
Šios matavimo juostelės yra skirtos nustatyti indėklų tarpelį.
1. Remove the bearing cap, wipe the journal and bearing shell clear of oil.
2. Place a piece of Flexigauge across the bearing at the crown (see Figure 1).
3. Install the bearing cap and using a Torque Wrench tighten the bolts to the correct tension.
4. DO NOT REVOLVE THE SHAFT OR BEARINGS.
5. Remove bearing cap. The Flexigauge will be adhering either to the bearing or shaft.
6. Compare the width of the flattened Flexigauge with the graduation of the envelope. The figure within the graduations indicates the clearance in thousandths of an inch of millimetres, depending on which side of the envelope is used. (See Figure 2).
7. Taper is indicated when Flexigauge is wider at one end than the other, the amount of taper being the difference between the readings. The widest part of the Flexigauge represents the area of least clearance. “Barrelling” of the shaft when the Flexigauge is wider in the centre of the bearing.
| ENGINE BEARINGS | ||||
|
CON ROD BEARING SET |
MAIN BEARING SET |
||
| Part# | Part# | |||
| 4B2904H |
4B2904HX |
5M2908H |
5M2908HX |
|
| Sizes | STD, .025, .25 | STD | STD, .025, .25 | STD |
| Oil Clearance | Standard | + 0.001" Extra | Standard | + 0.001" Extra |
| Half Type | Identical Halves | Upper & Lower | ||
| Material |
Tri-metal Hardened steel backs |
Tri-Metal | ||
| Min Std Shaft Size |
1.9995in / 50.787 mm |
2.0862 in / 52.991 mm |
||
| Max Std Shaft Size |
2.0003in / 50.807 mm |
2.0866 in / 53.000 mm |
||
| Min Std Tunnel Size |
2.1219 in / 53.897 mm |
2.2330 in / 56.717 mm |
||
| Max Std Tunnel Size |
2.1226 in / 53.913 mm |
2.2337 in / 56.735 mm |
||
| Max Wall at Crown |
0.0605in / 1.536 mm |
0.0600in / 1.523 mm |
0.0726 in / 1.843 mm |
0.0720 in / 1.830 mm |
| Max Overall Length |
0.768 in / 19.50 mm |
0.817 in / 20.75 mm (2908H/HX) 0.955 in / 24.25 mm (2909H/HX) |
||
| Notes | - | - | ||
|
Diagram |
|
2908H & HX - Positions 1,2,4,5
2909H & HX - Position 3
|
||
| THRUSTWASHER SET | ||||
| Part# | Material | |||
| Sizes | Notes | - | ||
