Click here to open old website version
Visos kategorijos
Parts by Car
Go
Parts by Car
Go
Dalys pagal:
Kategorija

2.8 2.9 3.2 3.6 VR6

Aktyvūs filtrai

Audi / VW 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL Race Series švaistikliniai indėklai 6B5530H-STD
Audi / VW 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL Race Series švaistikliniai indėklai...

Prekės kodas 6B5530H-STD
ACL Race series švaistikliniai indėklai
Audi / VW VR6 2.8 2.9 3.2 3.6 (BUB, BHK, AES, AUE, ABV, AAA, AMY)

146,00 €
Audi / VW 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL Race Series švaistikliniai indėklai 6B5530HX-STD
Audi / VW 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL Race Series švaistikliniai indėklai...

Prekės kodas 6B5530HX-STD (+0.001" papildomas tepimo tarpelis)
ACL Race Series švaistikliniai indėklai
Audi / VW VR6 2.8 2.9 3.2 3.6 (BUB, BHK, AES, AUE, ABV, AAA, AMY)

146,00 €
VAG 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL šoniniai indėklai 2T5532
VAG 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL šoniniai indėklai 2T5532

Prekės kodas 2T5532-STD
ACL šoniniai indėklai
VAG - 2.8 2.9 3.2 3.6 VR6 R32 R36

19,00 €
Audi / VW 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL Race pagrindiniai indėklai 7M5532H-STD
Audi / VW 2.8 2.9 3.2 3.6 VR6 R32 R36 ACL Race pagrindiniai indėklai 7M5532H-STD

Prekės kodas 7M5532H-STD
ACL Race Series pagrindiniai indėklai
Audi / VW - 2.8 2.9 3.2 3.6 VR6 R32 R36 (BUB, BHK, AES, AUE, ABV, AAA, AMY)

199,00 €
Kolbenschmidt indėklų tarpelio matavimo juostelių rinkinys 120000417001
Kolbenschmidt indėklų tarpelio matavimo juostelių rinkinys 120000417001

Prekės kodas 50009880.
Kolbenschmidt plastikinių matavimo juostelių rinkinys (10 vnt.).
Šios matavimo juostelės yra skirtos nustatyti indėklų tarpelį.

18,00 €
ACL indėklų tarpelio matavimo juostelių rinkinys AG-1 (Žalios sp.)
ACL indėklų tarpelio matavimo juostelių rinkinys AG-1 (Žalios sp.)
1. Remove the bearing cap, wipe the journal and bearing shell clear of oil.
2. Place a piece of Flexigauge across the bearing at the crown (see Figure 1).
3. Install the bearing cap and using a Torque Wrench tighten the bolts to the correct tension.
4. DO NOT REVOLVE THE SHAFT OR BEARINGS.
5. Remove bearing cap. The Flexigauge will be adhering either to the bearing or shaft.
6. Compare the width of the flattened Flexigauge with the graduation of the envelope. The figure within the graduations indicates the clearance in thousandths of an inch of millimetres, depending on which side of the envelope is used. (See Figure 2).
7. Taper is indicated when Flexigauge is wider at one end than the other, the amount of taper being the difference between the readings. The widest part of the Flexigauge represents the area of least clearance. “Barrelling” of the shaft when the Flexigauge is wider in the centre of the bearing.
16,00 €