Indėklai

Toyota 1/2JZGE 1/2JZGTE King Racing šoniniai indėklai TW284AM

13,00 EUR

BMW M3 E90 S65B40 ACL Race švaistikliniai indėklai 8B1580H-STD

Prekės kodas 8B1580H-STD
ACL Race Series švaistikliniai indėklai
BMW M3 E90 - 4.0 V8 (S65B40)

249,00 EUR

Mini Cooper S 1.6 Prince N12 N14 N16 N18 ACL Race švaistikliniai indėklai...

119,00 EUR

BMW 3.0 N54B30 N55B30 S55B30 ACL Race švaistikliniai indėklai 6B1584H-STD

209,00 EUR

Audi TTRS / RS3 CEPA CEPB ACL Race Series pagrindiniai indėklai 6M5563H-STD

Prekės kodas 6M5563H-STD
ACL Race Series pagrindiniai indėklai
Audi TTRS, RS3 - 2.5 (CEPA, CEPB)

195,00 EUR

BMW S63B44 M5 / M6 ACL Race švaistikliniai indėklai 8B1578H-STD

249,00 EUR

BMW M20 M50 M52 M54 ACL Duraglide švaistikliniai indėklai 6B1490-STD

Min Std Shaft Size	1.7707in / 44.975mm
Max Std Shaft Size	1.7713in / 44.991mm
Min Std Tunnel Size	1.8898in / 48.000mm
Max Std Tunnel Size	1.8904in / 48.016mm
Max Wall at Crown	0.0588in / 1.493mm
Max Overall Length	0.709in / 18.00mm

69,00 EUR

Mitsubishi 4G63 4G64 6 Bolt ACL Race švaistikliniai indėklai 4B1146H-STD

69,00 EUR

Audi R8 / Lamborghini Gallardo V10 5.0 5.2 King Racing švaistikliniai...

375,00 EUR

LADA 1200-1500 1973ON King Racing švaistikliniai indėklai CR4007XP-0.25

Position

Pairs & PN

XP	XP

C4007-PR	C4007-PR

Quantity

4

Crankshaft

47.813 / 47.833

Housing

51.331 / 51.346

Max Wall

1.730

Max Length

20.599

FL O/S

79,00 EUR

Lancia Delta Integrale 2.0 HF ACL Race Series švaistikliniai indėklai 4B2904H

ENGINE BEARINGS
	CON ROD BEARING SET		MAIN BEARING SET
	Part#		Part#
	4B2904H	4B2904HX	5M2908H	5M2908HX
Sizes	STD, .025, .25	STD	STD, .025, .25	STD
Oil Clearance	Standard	+ 0.001" Extra	Standard	+ 0.001" Extra
Half Type	Identical Halves		Upper & Lower
Material	Tri-metal Hardened steel backs		Tri-Metal
Min Std Shaft Size	1.9995in / 50.787 mm		2.0862 in / 52.991 mm
Max Std Shaft Size	2.0003in / 50.807 mm		2.0866 in / 53.000 mm
Min Std Tunnel Size	2.1219 in / 53.897 mm		2.2330 in / 56.717 mm
Max Std Tunnel Size	2.1226 in / 53.913 mm		2.2337 in / 56.735 mm
Max Wall at Crown	0.0605in / 1.536 mm	0.0600in / 1.523 mm	0.0726 in / 1.843 mm	0.0720 in / 1.830 mm
Max Overall Length	0.768 in / 19.50 mm		0.817 in / 20.75 mm (2908H/HX) 0.955 in / 24.25 mm (2909H/HX)
Notes	-		-
Diagram (Top View)			2908H & HX - Positions 1,2,4,5 2909H & HX - Position 3
THRUSTWASHER SET
Part#		Material
Sizes		Notes	-

89,00 EUR

ACL indėklų tarpelio matavimo juostelių rinkinys AG-1 (Žalios sp.)

1. Remove the bearing cap, wipe the journal and bearing shell clear of oil.
2. Place a piece of Flexigauge across the bearing at the crown (see Figure 1).
3. Install the bearing cap and using a Torque Wrench tighten the bolts to the correct tension.
4. DO NOT REVOLVE THE SHAFT OR BEARINGS.
5. Remove bearing cap. The Flexigauge will be adhering either to the bearing or shaft.
6. Compare the width of the flattened Flexigauge with the graduation of the envelope. The figure within the graduations indicates the clearance in thousandths of an inch of millimetres, depending on which side of the envelope is used. (See Figure 2).
7. Taper is indicated when Flexigauge is wider at one end than the other, the amount of taper being the difference between the readings. The widest part of the Flexigauge represents the area of least clearance. “Barrelling” of the shaft when the Flexigauge is wider in the centre of the bearing.

16,00 EUR